25LC Kbit SPI Bus Serial EEPROM The Microchip Technology Inc. 25AA/25LC *? Byte and Page-level Write Operations (25XX) is a 25LCI/SN Microchip Technology EEPROM k 64Kx8 V SER EE IND datasheet, inventory & pricing. 25LCI/SN from MICROCHIP >> Specification: EEPROM, Serial SPI, Kbit, 64K x 8bit, 20 MHz, SOIC, Technical Datasheet: 25LCI/SN Datasheet.

Author: Minos Mazugami
Country: Barbados
Language: English (Spanish)
Genre: Love
Published (Last): 1 January 2018
Pages: 318
PDF File Size: 5.61 Mb
ePub File Size: 10.94 Mb
ISBN: 432-3-84734-925-5
Downloads: 21850
Price: Free* [*Free Regsitration Required]
Uploader: Goltirisar

Anything above that will make it work just fine. We will walk through the code in small sections. I managed to figure it out. Chronological Newest First Hey guys, I’m in a bit of a bind. Here is a simple layout of the connections: In the control register each bit sets a different functionality.

Here we allocate the global variables we will be using later in the program. Since this is undesirable most of the time, the code below makes the page boundaries transparent for write operations. Thank you for your responses and assistance. Is this correctly read?

If you need larger capacity external memory, something like flash would be more suitable. This function could easily be changed to fill the array with data relevant to your application:.

There are status bits that can be used to pace the rate at which you feed new data to the SSP. Fri Jul 20, 9: You have checked that you see a clock.

This means you have to pay special attention to the datasheet when writing your interface code. CCS does not monitor this forum on a regular basis. However, there is some extra process time added when writing across a boundary.

  AR 385-95 PDF

An explanation of bit masks can be found here. Last edited by treitmey on Fri Jul 20, Next we send our bytes of data from our buffer array, one byte after another without pause. This means that any write operation, no matter how few bytes, takes the same amount of time, about 3. I keep looking into it, but if you notice anything else or have any other suggestions please let me know.

It looks like they already have done the heavy lifting for me in regard to setting up the clock and power. If I was missing any thing, Please guide me to complete this task. Introduction to Microcontrollers Mike Silva. Each time through the loop we increment the eeprom address to read.

Additionally, I did create a ns and microsecond delay functions I can also test as well, but I’ll try the ms delay with the system tick first. EEPROM is non-volatile memory usually used to hold small amounts such as system parameters that must be retained between power resets.

【25LC512-1/P MICROCHIP】Electronic Components In Stock Suppliers in 2018【Price】【Datasheet PDF】USA

Instructions are sent 25l512 8 bit operational codes opcodes and are shifted in on the rising edge of the data clock. If anyone can help me out it would be much appreciated. I see what appears to be pulse more like sloped triangles. Have you checked the data which is received? Registers generally serve three purposes, control, data and status.

It’s memory is organized as pages of bytes each. I configure SSP1 as follows: Thank you for the reply Martin.

25LC512 Datasheet PDF

I have checked it in Proteus. In the main loop it reads that data back out, one byte at a time and prints that byte out the built in serial port. The problem is that I’m not sure if my connections are right or if my software is configured correctly.

  CURTEA REGALA DE BUCATE PDF

We send the 16 bit address to begin writing at in two bytes, Most Significant Bit first.

25LC – Memory – Memory

I have to find out how to use timers as delays, for milliseconds using system tick isn’t going to cut it. Display posts from previous: Usually each bit in a control register effects a particular setting, such as speed or adtasheet. Fri Jul 20, 8: Easy with even quite small capacitors.

Control registers code control settings for various microcontroller functionalities. These modes control whether data is shifted in and out on the rising or falling edge of the data clock signal, and whether the clock is idle when high or low.

This is what is causing me greif I have also checked clock with an oscilloscope not logic analyzer on hand unfortunately. You can also send only 1 byte instead of multiple byte, if this makes it easier for you to bring system up. They start with a ” ” and do not end with semi-colons. This deselects the device and avoids any false transmission messages due to line noise:.

Previous 1 2 Next. Hi Nick, It seems to me that the ns from the datasheet is the minimum time delay needed for it to work.